品牌：欧莱斯, 型号：MPE, 印刷方式：丝印移印, 连接料：树脂油型, 承印物：电镀, 干燥形式：自然干燥, 颜色：不限, 产地：德国, 叠印性：强, 外观：膏状, 含水量：0.0021%, 颗粒细度：99.99μm, 粘度：100S, 附着强度：100, 稳定性：10, 流动性：0.013mm, 干燥时间：3-5min, 渗透性：10μm, 储存温度：22-23℃, 包装规格：1008ml, 保质期：48, 适用范围：真空电镀、水电镀、强化电镀、金属电镀、塑胶电镀、五金电镀, 特性：免烘烤、单组份、双组份、自干, 外光：高光泽、高色彩、高硬度, 特质：耐酒精、耐酸碱、耐汽油、耐摩擦、抗腐蚀, 印刷方式：丝印、移印、喷涂,
75电镀强化系列油墨
油墨特性： 主要用于电镀表面、强化表面、真空电镀表面．PU表面．UV表面等材料上，具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及耐磨擦之特点。
印刷：丝印移印均可。 表干及实干时间：表干时间自然挥发5-10分钟；实干时间在24小时以内。
稀释及清洗：SV3慢干开油水、UVK1（移印开油水）同时可使用718洗网水清洗。 测试方法（干燥后）：
1、3m胶纸粘在画有百格的油墨表面，45度角迅速拉起不脱油; 2、纯度99%的工业酒精，一千克砝码用棉布包住在油墨表面，以水平力来回拉200次无脱色; 3、
耐磨：橡皮擦500g力水平来回擦500次。 使用方法： 1、使用前应充分搅拌，用后随时封闭； 2、搅拌时加开油水10-15%，稀释到印刷粘度；
3、网板塞网时可用洗网水清洗； 4、不得与其它类型油墨混合使用。 注意事项：
1、塑胶材料的外观相似，但可能会是不同的材料，客户需试印确定其符合要求后，再批量印刷； 2、在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可;
3、环境温度过高，将会影响油墨原有质量； 4、根据气候变化，请远离火源，阴暗环境下存放。
75
plating strengthening series ink characteristics: mainly used in plating
surface, enhanced surface, vacuum platingsurface.PU surface.UV surface and
other materials, with a high color, high color, high covering power, alcohol
resistant and wear resistance, high stability. Printing: silk screen printing
can be. Table dry and work time: surface dry time natural volatile 5-10
minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open
water,UVK1 (printing open water) also can use 718 washing network water
cleaning. Test method (completely dry): 1,3M adhesive tape sticky ink surface
adhesion in painting,45 degree angle quickly pulled off the oil; 2, purity 99%
of industrial alcohol, using cotton bag in the surface of the inkone kilogram
weight to horizontal force and pull 200 timeswithout decolorization; 3, wear:
rubber eraser 500g forcelevel wipe 500 times back and forth. Method of use:
1,before the use should be fully mixing, be closed after use;2, stirring an
additional oil 10-15%, dilution to printingviscosity; 3, mesh plug mesh can be
used when washing network water cleaning; 4, shall not be mixed with othertypes
of ink. Note: 1, the plastic material of similar appearance, but may be of
different materials, customers need to try to determine its requirements, and
then batchprinting; 2, in the printing process, such as drawing or spread out,
may be appropriate to add some slow dry pastecan; 3, the ambient temperature is
too high, it will affect thethe quality of the original ink; 4, according to
the climate change, please stay away from fire, stored in dark